Socket Size Chart Pdf
Socket size chart pdf
Six Point Standard Sockets (3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1)
What is the most common size socket?
The most commonly used types are 8 mm, 10 mm and 14 mm sockets.
What are the SAE socket sizes?
The most commonly used and sold SAE sizes for wrenches and sockets are:
- 5/16″
- 3/8″
- 7/16″
- 1/2″
- 9/16″
- 5/8″
- 11/16″
- 3/4″
What size nut fits in 12 mm socket?
Metric Fasteners - Wrench size needed for Driving common Nuts | ||
---|---|---|
Screw Size | Wrench Size * | Alt Size, Flange Nuts ** |
M8 | 13mm | 13mm |
M10 | 17mm | 15mm |
M12 | 19mm | 18mm |
How do you read socket sizes?
Socket set sizes These are always given in imperial measurements, and will usually be either 1/4", 3/8", 1/2", 3/4" or 1". The size of the socket head (the part that fits over or into a fastener). Usually, the smaller the drive socket size is, the smaller the socket head size will be, and vice versa.
Are 3/4 and 19mm the same?
19mm = 3/4 inch. 20mm = 25/32 inch. 21mm = just over 13/16 inch. 22mm = almost 7/8 inch.
What are the 3 types of sockets?
Three types of sockets are supported:
- Stream sockets allow processes to communicate using TCP. A stream socket provides bidirectional, reliable, sequenced, and unduplicated flow of data with no record boundaries.
- Datagram sockets allow processes to use UDP to communicate. ...
- Raw sockets provide access to ICMP.
Which socket size is best?
Drive Size
- ½-inch drive size sockets are for high-torque applications like automotive wheel replacement and when you are using a breaker bar.
- ⅜-inch drive size sockets are the most common and most available. ...
- ¼-inch drive size sockets are ideal when you are in tight spaces or when you are working with recessed nuts.
Whats bigger 3/8 or 1/4 socket?
3/8 is expressed as 0.375 as a decimal and 1/4 is expressed as 0.25 in its decimal form. It is clear that the value of 3/8 is more than 1/4. Hence, it is bigger.
Does SAE mean standard?
SAE, or standard, is used on most domestic models, while metric applies to foreign or non-domestic vehicles. Socket sets and wrench sets are among the most used tools in cases where size measuring differences are important. Notably, SAE tools are measured in fractions of inches, from 5/32 to 2 ½ inches.
What are the 3 common sizes of ratchets?
Available with different drive sizes — 1/4 inch, 1/2 inch and 3/8 inch — to operate different size sockets. Most operate with a geared drive; those with a higher tooth count let you operate the tool with a smaller swinging motion, which is useful when there's little room to move the handle.
What does SAE stand for in measurement?
Standard American English and the Metric System Today, measuring in feet and inches is part of the Standard American English (SAE) or Imperial units of measurement, along with volumes like gallons and fluid ounces and weights like pounds.
What size is M10 in mm?
Size | Clearance Hole mm | Tapping Drill (std Pitch) |
---|---|---|
M6 | 6.5 | 5.0 mm |
M8 | 9 | 6.75 mm |
M10 | 11 | 8.5 mm |
M12 | 14 | 10.25 mm |
What size bolt is M10?
Steel bolt with M10 metric thread. Metric threads are designated with a capital M plus an indication to their nominal outer diameter and their pitch: This bolt is M10 x 1.5 - which means the outside diameter is 10mm and the threads are 1.5mm apart (the most common thread pitch for M10).
How do I calculate nut size?
Bolts are measured in length of shank, bolt head size, width of shank (the diameter of the threaded bolt body) and the thread pitch (the size of the thread). Nuts are measured by the width of the hex shape and by their thread pitch.
What are the different types of sockets?
Quick Check
- Common Types of Socket and Their Uses.
- Hex Sockets.
- Spark Plug Sockets.
- Impact Sockets.
- Universal Joints Sockets.
- Insulated Sockets.
- Socket Bits.
- Pass-Through Sockets.
How do I choose a socket set?
When selecting a socket set, you should think about where you will be using it as well as what it must include. Instead, try to buy the socket set that will expand your tool collection in the best way, and concentrate on the size range of sockets included, both standard and deep lengths, in metric and imperial sizes.
How are 12 sockets measured?
Socket Sizes:SAE (INCH, fraction) & Metric (mm) In the current market, socket sizes are divided into two systems: SAE (imperial, measured in inches) and metric (measured in millimeters). Both 6-point and 12-point sockets are measured using these two systems.
Can I use a 3/4 socket instead of a 19mm?
No, there's no need to get a 19mm socket, and it will present no difference in performance just because the number on the side is different.
What size is a 19 mm in standard?
Bolt Diameter | Metric | Standard |
---|---|---|
1/2" | 19mm | 3/4" |
9/16" | 21mm | 13/16" |
22mm | 7/8" | |
5/8" | 24mm | 15/16" |
Post a Comment for "Socket Size Chart Pdf"